Peptide Initiative

Injection guide · Growth Hormone

How to inject Alexamorelin

A next-generation growth hormone releaser that converts to hexarelin in your body for enhanced GH, cortisol, and unique aldosterone stimulation.

SubcutaneousRoute
4 recommendedSites
Multiple times dailyFrequency

01 · Preparation

What you'll need

  • Bacteriostatic water or normal saline (typically 1-2 mL per vial)
  • Sterile syringe and needle (25-27 gauge preferred)
  • Alcohol swabs for vial sterilization
  • Sterile vial for storage

Pro tip

Prepare all supplies on a clean surface before you begin. Having everything ready makes the process smoother and more sterile.

02 · Mixing

Reconstitution steps

  1. Wash your hands thoroughly with soap and water. Gather all supplies on a clean, flat surface.
  2. Remove the plastic cap from the peptide vial and wipe the rubber stopper with an alcohol swab. Let it air dry.
  3. Draw the appropriate amount of bacteriostatic water into a sterile syringe.
  4. Insert the needle into the vial at an angle, aiming at the inside wall of the vial. Slowly push the plunger to let the water trickle down the glass wall -- do NOT squirt directly onto the powder.
  5. Once all water is added, gently swirl the vial in a slow circular motion. Never shake the vial, as this can damage the peptide bonds.
  6. Continue swirling until the powder is completely dissolved and the solution is clear. If particles remain, let the vial sit for a few minutes and swirl again.
  7. Label the vial with the date of reconstitution, the peptide name, and the concentration (e.g. 250mcg per 0.1mL).

Example calculation

If vial contains 1 mg alexamorelin and you add 1 mL bacteriostatic water, concentration = 1 mg/mL (1000 mcg/mL). To draw 100 mcg, inject 0.1 mL.

Dose calculation

Draw volume (mL) = Desired dose (mcg) ÷ Concentration (mcg/mL). For 150 mcg from 1000 mcg/mL solution: 150 ÷ 1000 = 0.15 mL

Pro tip

Always add the bacteriostatic water slowly, letting it run down the side of the vial. Never shake the vial -- swirl gently to avoid damaging the peptide.

03 · Location

Choosing your injection site

  • Site 01AbdomenPinch the skin 2 inches from navel. Avoid the area directly around the belly button. Rotate between left and right sides.
  • Site 02Outer ThighMiddle third of the outer thigh. Keep at least 4 inches above the knee and below the hip. Alternate legs each injection.
  • Site 03Lateral chest wall above waistFollow your provider's instructions for this injection site. Rotate sites regularly to prevent tissue damage.
  • Site 04Upper ArmBack or outer area of the upper arm. This site may require assistance from another person for proper technique.

Rotate between 4 sites to prevent tissue buildup and ensure consistent absorption.

Pro tip

Rotate your injection sites with each dose to prevent lipohypertrophy (buildup of fatty tissue). Keep a simple log of where you last injected.

04 · Step by step

Injection technique

  1. Clean injection site with alcohol swab and let dry 10-15 seconds
  2. Pinch skin at injection site to create small fold
  3. Insert needle at 45-90 degree angle (steeper = more subcutaneous, shallower = easier)
  4. Push plunger slowly to minimize discomfort and ensure proper dispersion
  5. Withdraw needle, release skin, and apply gentle pressure for 5 seconds

Pro tip

This peptide uses subcutaneous injection preferred for consistent gh response; intravenous only in clinical/research settings. Inject at a 45-90 degree angle into pinched skin. Aspirate before injecting to ensure you haven't hit a blood vessel.

05 · Timing

Your schedule

How often

Multiple times daily

Best time

Morning injection on empty stomach 30-60 minutes before food maximizes GH response; second dose in late afternoon if dosing twice daily

Dose levels, food and stacking notes and a sample day are on the Alexamorelin dosing protocol.

06 · Preservation

Proper storage

Before mixing

Lyophilized powder at 2-8°C (refrigerator) in dark, dry location. Protect from light and moisture. Properly sealed vial lasts 1-2 years.

After mixing

Reconstituted solution at 2-8°C with bacteriostatic water. Use within 14-30 days. Discard if cloudy, discolored, or shows particles.

Shelf life after mixing

14-30 days when stored at 2-8°C with proper bacteriostatic agent; shorter if kept at room temperature

Signs of degradation

Discard the vial immediately if you notice any of these:

  • Solution becomes cloudy or milky instead of clear
  • Visible particles or crystallization in vial
  • Color change to yellow, brown, or any discoloration
  • Unusual odor or signs of bacterial contamination

07 · Important

Safety reminders

When to stop

  • Severe mood changes or anxiety that don't improve with dose adjustment
  • Signs of cardiovascular stress (chest pain, irregular heartbeat, severe headaches)
  • Uncontrolled blood sugar elevation or worsening of diabetes
  • Persistent allergic reactions or injection site infections
  • Completion of planned 4-6 week cycle (take break before restarting)
  • New or worsening joint problems that limit training

This is research compound information, not medical advice. Consult a healthcare provider before starting, especially if you have existing health conditions. Stop immediately if you experience serious side effects and seek medical attention.

Clean technique checklist

  • Wash hands thoroughly with soap and water before handling supplies
  • Swab vial tops and injection site with alcohol and let dry
  • Never touch the needle tip or allow it to contact non-sterile surfaces
  • Use a new syringe and needle for each injection
  • Dispose of used sharps in a proper sharps container
  • Store reconstituted peptides according to the storage instructions above

Continue

This guide is for informational purposes only and is not medical advice. Always consult with a qualified healthcare provider before starting any peptide protocol. Individual responses may vary.